O-ring to seal the vacuum actuator shaft in its housing. Suits only LT95 gearboxes. Vacuum actuators are often mis-diagnosed as faulty when it is only this o-ring at fault. Make sure you test these units in both directions. If it works to engage but not...

O-ring to seal the speedo drive insert into the rear output housing. Suits LT95 and LT230. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you...

Needle roller bearing for the rear of the mainshaft in all versions of the LT95. This fits in the PTO plate on the rear of the transfer case (or in the 3rd axle output of the 6x6). *** Specific Brand Part *** This product is not specific to one brand...

Nylon insert for the cast iron clutch throwout lever found on all LT95, LT85 and LT77 gearboxes. Also found on the R380 gearbox when fitted to the Td5 engine or Rover V8. DOES NOT suit the stamped steel lever normally found in the 300Tdi variants.***...

The small internal oil seal for the front of the LT95 mainshaft*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you with the same or similar part...

The gasket for the cast iron oil pump housing/input seal housing for all versions of the LT95 gearbox. This gasket is included in our Perentie clutch kit KLR-CK4. Also included in the LT95 gasket kit 606754. The cover plate for the oil pump...

Special snap ring for the front of the mainshaft to retain the 3rd/4th synchro assembly. Suits all LT95 gearboxes. Before you fit this ring grind each end on an angle to make it easier to remove with snap ring pliers. *** Specific Brand Part ***...

Flat torrington needle roller bearing for either side of the 2nd and 3rd gears in all LT95 gearboxes. 3x per gearbox. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific...

Flat torrington needle roller bearing for either side of the 1st gear in all LT95 gearboxes. 2x per gearbox. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we...

Roller bearing that fits on the front end of the mainshaft into the rear of the input shaft. Suits all LT95 gearboxes. 1x per gearbox. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description...

Corteco brand (good stuff) oil seal fitted in the rear of the oil pump housing on the LT95 input shaft. Unless you like removing gearboxes don't risk a cheap oil seal here. This seal is included in our clutch kit KLR-CK4. To fit this you will need to...

Seals the back of the reverse idler shaft into the transfer case. Suits LT95 and LT95A gearboxes. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide...

Spigot bush to fit all Rover push-rod V8 engines (manual only)(3.5, 3.9, 4.0, 4.2 and 4.6). Also suits the 110 County with the LT95 or LT85 gearbox. Fits all Perentie models with the LT95 gearbox. This bush is supplied as part of our heavy duty clutch...

O-ring to seal the rear of the intermediate shaft on the LT95 and LT95A transfer case (roller and taper bearing types). *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific...

Front output bearing for the LT95/LT95A gearbox (where the front propshaft connects). *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you with the...