CV joint support bearing that fits in the back of the front stub axle FTC3154. Suits all Defender from VIN LA onwards including Puma models. Suits all Discovery 1. Also suits Range Rover Classic from approximately 1986. You will need to strip your...

Rubber type drive flange/axle cap for all Defenders from '92, all Discovery 1 and all Range Rover Classic from '92. This cap is shorter (or lower) than the earlier ones. This is the genuine one; the cheap ones don't last anywhere near as long. We...

Inner axle oil seal fitted to the rear of the front stub axle. Suits all Discovery 1 and all Defenders from approx. 1992 on. This seal fits in behind the CV joint bearing. Suits the stub axle FTC3154 (crescent type lock washer).*** Specific Brand Part...

Diff pinion oil seal to suit the "long nose" Rover diff as fitted to all Range Rover Classic (front and rear), all Discovery 1 and 2 (front and rear), all Defender front, all 110 and Perentie front. Also suits the front output seal for all LT95 gearboxes...

Inner axle seal fitted to the back of the swivel ball. Suits Defenders with 4-wheel disc brakes; suits Discovery 1 and Puma Defenders. Will also suit late Range Rover Classic. *** Specific Brand Part *** This product is not specific to one brand. If the...

Rear stub axle for all Defenders from about 2002 onwards. Suits only those models with the "Wolf" or P38A type rear diff (DOES NOT suit Salisbury diff models - see FTC1740). Rear stub axle for Range Rover Classic and Discovery 1 from approx. '92 on (JA...

Usually not an item that requires regular replacement, but we get asked for these often enough so here they are. This is the thrust washer for the "crescent" type front stub axle on all Defenders from VIN KA to TA. This thrust washer fits between the...

A half-moon type hub nut lock washer for all Defenders from LA onwards. Discovery 1 and Range Rover Classic from JA (approx. '92) onwards. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the...

Half-moon type lock washer. Suits all Defender from VIN LA onwards including Puma models. Suits all Discovery 1. Also suits Range Rover Classic from approximately 1986. You will need to strip your front hubs to confirm what you actually have. You will...

These are probably the most abused nuts on a Genuine Land Rover - usually undone and refitted with a cold chisel. If yours are beyond redemption just replace them, and treat yourself to the proper hub nut spanner 606435.Suits any Genuine Land Rover that...

For the adjustable type wheel bearings. Half moon type hub nut lock washer on all Range Classic, Discovery 1 and Defender to approximately 1992. NOTE: Early (pre '85) 110 and RRC will have the squared keyway type lock washer part number 217353. NOTE:...

Drive flange bolt (Grade 10.9) for all Defenders from 1994 on. Also suits all Discovery 1 and all Range Rover Classic from approx. 1992. M10 x45mm thread.*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows...

Diff filler and drain plug for many, many Genuine Land Rover models. This is the taper BSP thread type that accepts a standard 1/2" drive ratchet/breaker bar. Also suits LT230 transfer cases. This one DOES NOT have a magnet. *** Specific Brand Part ***...

TIMKEN Bottom swivel bearing for all 110/Defender up to KA (approx. '93) and Defender Puma. Also suits all Perentie 4x4 and 6x6. Also suits all ABS equipped Defenders (bottom bearing only). Top and bottom swivel bearing for all Range Rover Classic and...

The proper tool for undoing , adjusting and tensioning Genuine Land Rover wheel bearings. A cold chisel IS NOT a suitable replacement for this tool. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the...

Front inner axle oil seal (fits into the rear of the swivel ball). Suits Perentie, 110, Defender (with rear drum brakes), Range Rover Classic (up to about '94). When these leak your one-shot swivel grease makes its way into the front diff oil. A small...

Circlip fitted to the end of each axle against the drive flange. Suits all Perentie, all Defender, all 110 County, all Discovery 1 and Range Rover Classic that use a rubber drive flange cap. *** Specific Brand Part *** This product is not specific to one...

Outer (small) diff pinion bearing for the Rover-type diff to front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part *** This...

Inner (large) diff pinion bearing for the Rover-type diff to suit front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part ***...

Usually not an item that requires regular replacement, but we get asked for these often enough so here they are. This is the thrust washer for the "key" type front stub axle on all Perenties, and all Defenders up to VIN KA. Also fits early Range Rover...