Diff filler and drain plug for many, many Genuine Land Rover models. This is the taper BSP thread type that accepts a standard 1/2" drive ratchet/breaker bar. Also suits LT230 transfer cases. This one DOES NOT have a magnet. *** Specific Brand Part ***...

TIMKEN Bottom swivel bearing for all 110/Defender up to KA (approx. '93) and Defender Puma. Also suits all Perentie 4x4 and 6x6. Also suits all ABS equipped Defenders (bottom bearing only). Top and bottom swivel bearing for all Range Rover Classic and...

Rear bearing for the centre diff in all LT95 and LT230 transfer cases. *** Specific Brand Part ***This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you with the same or similar...

The proper tool for undoing , adjusting and tensioning Genuine Land Rover wheel bearings. A cold chisel IS NOT a suitable replacement for this tool. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the...

Push rod clip for all models with a cast iron throwout lever - some Defender, 110, Perentie, Discovery 1 and Range Rover Classic (V8 only) and Discovery 2. Suits LT95, LT85 and LT77 (and R380 behind Td5 engines). *** Specific Brand Part *** This product...

The plastic C-clip used on all cast iron throwout levers for all LT95, LT85 and LT77 gearboxes. Also found on the R380 gearbox when fitted to the Td5 engine or Rover V8. DOES NOT suit the stamped steel lever normally found in the 300Tdi variants. ***...

The 2-hole lock tab normally fitted to the mounting bolts for the 3- and 4-bolt power steering boxes. Suits all Range Rover Classic, all Discovery 1, all Defenders and all Perenties (including those with manual steering boxes). Two per vehicle. These can...

Front inner axle oil seal (fits into the rear of the swivel ball). Suits Perentie, 110, Defender (with rear drum brakes), Range Rover Classic (up to about '94). When these leak your one-shot swivel grease makes its way into the front diff oil. A small...

O-ring to seal the speedo drive insert into the rear output housing. Suits LT95 and LT230. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you...

Nylon insert for the cast iron clutch throwout lever found on all LT95, LT85 and LT77 gearboxes. Also found on the R380 gearbox when fitted to the Td5 engine or Rover V8. DOES NOT suit the stamped steel lever normally found in the 300Tdi variants.***...

Shock absorber bush for 110/Defender/RRC and Disco 1. Fit front shocks upper and lower and rear shocks lower. Note: On the later models your rear axle may have cups welded to the lower shock mount. If it does you need shock bushes part number RNF100090L...

Spigot bush to fit all Rover push-rod V8 engines (manual only)(3.5, 3.9, 4.0, 4.2 and 4.6). Also suits the 110 County with the LT95 or LT85 gearbox. Fits all Perentie models with the LT95 gearbox. This bush is supplied as part of our heavy duty clutch...

Circlip fitted to the end of each axle against the drive flange. Suits all Perentie, all Defender, all 110 County, all Discovery 1 and Range Rover Classic that use a rubber drive flange cap. *** Specific Brand Part *** This product is not specific to one...

Outer (small) diff pinion bearing for the Rover-type diff to front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part *** This...

Inner (large) diff pinion bearing for the Rover-type diff to suit front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part ***...

Dust and mud boot fitted to FRONT of the handbrake backing plate. Suits LT95 and LT230 handbrakes with the indirect handbrake cable (this boots seals the actuating rod going into the backing plate). Suits Perentie, early Defender and 110, some Range...

Two long bolts to secure the a-frame ball joint assembly to the rear a-frame arms (just above the rear diff). Suits Range Rover Classic, Discovery 1, 110 County, Defender and 4x4 Perentie. The nuts for these bolts are 1/2"UNF  - see NY608042...

Usually not an item that requires regular replacement, but we get asked for these often enough so here they are. This is the thrust washer for the "key" type front stub axle on all Perenties, and all Defenders up to VIN KA. Also fits early Range Rover...