LT95 Mainshaft Oil Seal (Small Internal) $12.60 The small internal oil seal for the front of the LT95 mainshaft*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific... Add to Cart
LT95 Oil Pump Housing Gasket $8.80 The gasket for the cast iron oil pump housing/input seal housing for all versions of the LT95 gearbox. This gasket is included in our Perentie clutch kit KLR-CK4. Also included in the LT95 gasket... Add to Cart
LT95 Mainshaft Snap Ring (Front) $22.00 Special snap ring for the front of the mainshaft to retain the 3rd/4th synchro assembly. Suits all LT95 gearboxes. Before you fit this ring grind each end on an angle to make it easier to remove...
LT95 Flat Torrington Bearing, 2nd/3rd Gear $15.40 Flat torrington needle roller bearing for either side of the 2nd and 3rd gears in all LT95 gearboxes. 3x per gearbox. *** Specific Brand Part *** This product is not specific to one brand. If the... Add to Cart
LT95 Flat Torrington Bearing, 1st Gear $9.90 Flat torrington needle roller bearing for either side of the 1st gear in all LT95 gearboxes. 2x per gearbox. *** Specific Brand Part *** This product is not specific to one brand. If the product... Add to Cart
LT95 Mainshaft Front Roller Bearing $47.94 Roller bearing that fits on the front end of the mainshaft into the rear of the input shaft. Suits all LT95 gearboxes. 1x per gearbox. *** Specific Brand Part *** This product is not specific to one...
LT95 Input Shaft Seal $17.00 Corteco brand (good stuff) oil seal fitted in the rear of the oil pump housing on the LT95 input shaft. Unless you like removing gearboxes don't risk a cheap oil seal here. This seal is included in... Add to Cart
LT95 Reverse Idler Shaft O-Ring $22.00 Seals the back of the reverse idler shaft into the transfer case. Suits LT95 and LT95A gearboxes. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or... Add to Cart
Front Shock Absorber Bush $5.70 Shock absorber bush for 110/Defender/RRC and Disco 1. Fit front shocks upper and lower and rear shocks lower. Note: On the later models your rear axle may have cups welded to the lower shock mount... Add to Cart
Spigot Bush, Rover V8 (3/4") $7.50 Spigot bush to fit all Rover push-rod V8 engines (manual only)(3.5, 3.9, 4.0, 4.2 and 4.6). Also suits the 110 County with the LT95 or LT85 gearbox. Fits all Perentie models with the LT95 gearbox... Add to Cart
Axle/CV Circlip $4.40 Circlip fitted to the end of each axle against the drive flange. Suits all Perentie, all Defender, all 110 County, all Discovery 1 and Range Rover Classic that use a rubber drive flange cap. ***... Add to Cart
Outer Diff Pinion Bearing (Rover) $44.00 Outer (small) diff pinion bearing for the Rover-type diff to front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender... Add to Cart
Inner Diff Pinion Bearing (Rover) $66.30 Inner (large) diff pinion bearing for the Rover-type diff to suit front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear... Add to Cart
LT95 Intermediate Shaft O-Ring $4.20 O-ring to seal the rear of the intermediate shaft on the LT95 and LT95A transfer case (roller and taper bearing types). *** Specific Brand Part *** This product is not specific to one brand. If the... Add to Cart
Handbrake Actuating Rod Boot $11.00 Dust and mud boot fitted to FRONT of the handbrake backing plate. Suits LT95 and LT230 handbrakes with the indirect handbrake cable (this boots seals the actuating rod going into the backing plate)... Add to Cart
Defender/110 Bonnet Buffer $5.50 Rubber buffer for the four bonnet supports on the Defender/110/Perentie bonnets. 4x per vehicle. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or... Add to Cart
Rear A-Frame Lower Mounting Bolt $9.50 Two long bolts to secure the a-frame ball joint assembly to the rear a-frame arms (just above the rear diff). Suits Range Rover Classic, Discovery 1, 110 County, Defender and 4x4 Perentie. The nuts... Add to Cart
Diff Pinion Flange, 4-Spline Rover Diff $49.01 Early 4-spline diff pinion flange. Replacing this flange is a far, far better option than using a speedi-sleeve. Usually only fitted to earlier Range Rover Classic or 110s; but they often find their... Add to Cart
Hub Nut Locking Washer, Square Key $1.50 "Key" type locking washer for the front of the Perentie 4x4 and 6x6, also 110 and early RRC. If your stub axle has a 5mm wide keyway this is the correct lock washer. You require one per hub. ***... Add to Cart
Hub Thrust Washer, Key Type Was: $3.20 Now: $1.50 On Sale Usually not an item that requires regular replacement, but we get asked for these often enough so here they are. This is the thrust washer for the "key" type front stub axle on all Perenties, and... Add to Cart
LT95 Front Output Bearing $54.51 Front output bearing for the LT95/LT95A gearbox (where the front propshaft connects). *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the... Add to Cart
