TIMKEN Bottom swivel bearing for all 110/Defender up to KA (approx. '93) and Defender Puma. Also suits all Perentie 4x4 and 6x6. Also suits all ABS equipped Defenders (bottom bearing only). Top and bottom swivel bearing for all Range Rover Classic and...

Rear bearing for the centre diff in all LT95 and LT230 transfer cases. *** Specific Brand Part ***This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you with the same or similar...

The proper tool for undoing , adjusting and tensioning Genuine Land Rover wheel bearings. A cold chisel IS NOT a suitable replacement for this tool. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the...

Flame trap to suit the carburettor model 3.5 Rover V8 as fitted to the Range Rover Classic and V8 110 County. One required for each rocker cover.*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the...

Clutch slave cylinder to suit Defender 200Tdi fitted with LT77 gearbox. Also suits Series III models.*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may...

Push rod clip for all models with a cast iron throwout lever - some Defender, 110, Perentie, Discovery 1 and Range Rover Classic (V8 only) and Discovery 2. Suits LT95, LT85 and LT77 (and R380 behind Td5 engines). *** Specific Brand Part *** This product...

The plastic C-clip used on all cast iron throwout levers for all LT95, LT85 and LT77 gearboxes. Also found on the R380 gearbox when fitted to the Td5 engine or Rover V8. DOES NOT suit the stamped steel lever normally found in the 300Tdi variants. ***...

Front inner axle oil seal (fits into the rear of the swivel ball). Suits Perentie, 110, Defender (with rear drum brakes), Range Rover Classic (up to about '94). When these leak your one-shot swivel grease makes its way into the front diff oil. A small...

O-ring to seal the speedo drive insert into the rear output housing. Suits LT95 and LT230. *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand, we may provide you...

Nylon insert for the cast iron clutch throwout lever found on all LT95, LT85 and LT77 gearboxes. Also found on the R380 gearbox when fitted to the Td5 engine or Rover V8. DOES NOT suit the stamped steel lever normally found in the 300Tdi variants.***...

Spigot bush to fit all Rover push-rod V8 engines (manual only)(3.5, 3.9, 4.0, 4.2 and 4.6). Also suits the 110 County with the LT95 or LT85 gearbox. Fits all Perentie models with the LT95 gearbox. This bush is supplied as part of our heavy duty clutch...

Circlip fitted to the end of each axle against the drive flange. Suits all Perentie, all Defender, all 110 County, all Discovery 1 and Range Rover Classic that use a rubber drive flange cap. *** Specific Brand Part *** This product is not specific to one...

Outer (small) diff pinion bearing for the Rover-type diff to front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part *** This...

Inner (large) diff pinion bearing for the Rover-type diff to suit front and rear of all Range Classic; all Discovery 1 and 2, all Defender/110/Perentie (front only). DOES NOT fit the P38A or rear Defender from approx. '02 on. *** Specific Brand Part ***...

O-ring to seal the rear of the intermediate shaft on the LT95 and LT95A transfer case (roller and taper bearing types). *** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific...

"DIESEL FUEL" decal fitted to the filler neck on Series, County, Perentie and Defender models. Will also fit RRC.*** Specific Brand Part *** This product is not specific to one brand. If the product photo shows or the description lists a specific brand,...

Early 4-spline diff pinion flange. Replacing this flange is a far, far better option than using a speedi-sleeve. Usually only fitted to earlier Range Rover Classic or 110s; but they often find their way into later model vehicles. These are usually...

"Key" type locking washer for the front of the Perentie 4x4 and 6x6, also 110 and early RRC. If your stub axle has a 5mm wide keyway this is the correct lock washer. You require one per hub. *** Specific Brand Part *** This product is not specific to one...

Usually not an item that requires regular replacement, but we get asked for these often enough so here they are. This is the thrust washer for the "key" type front stub axle on all Perenties, and all Defenders up to VIN KA. Also fits early Range Rover...